信誉第一网投平台-澳门十大网赌信誉平台-登录

推荐产品
  • 压铸模温机 压铸模温机,压铸机专用模温机,使用工作温度高达350℃,采用...
  • 集中供料系统 集中供料系统采用微机集中自动控制,实现了对粒料的24小时连续...
  • 自动吸料机 300G微电脑全自动吸料机产品(又称真空吸料机,自动吸料机,...
  • 水式模温机 水式模温机 达安泰企业专业生产模温机,高光模温机,高光注塑...
  • 中央供料配件 中央供料配件-中央控制台 操作界面与运转状态显示面板数字化...
  • 中央供料系统 中央供料系统是为注塑车间的塑料产品生产而设计的,实现了不间断...
  • 塑料干燥机 标塑料干燥机特点:原料接触面为不锈钢设计。 精密压铸的铝制外...
  • 吸粉机 吸粉机原理的详细先容: 真空吸粉机,又称作:气动真空给料机...
  • 低速粉碎机 低速粉碎机系列特点: 1、 慢速塑料破碎机属于无筛网型塑料回...
  • 自动吸料机 自动吸料机:5HP真空自动吸料机产量高;达到时产800公斤输...
产品详情
  • 产品名称:250T立式液压打包机

  • 产品型号:
  • 产品厂商:天天自动
  • 产品文档:
你添加了1件商品 查看购物车
简单先容:
250T立式液压打包机 金属铜打包机(不锈钢打包机), 配用动力:22KW,台时产量:3-5个包块,包重:800-1500KG, 油缸:Φ190*2支,操作方便,接上电源后打包 , 专用于一切轻泡、松散物料的打包。可应用于用于有色金属板材及型材和轻簿型塑料,棉、羊毛、废纸、废纸箱、废纸板、纱线、塑料、布匹、编织袋、针织绒、麻、麻袋、毛条、毛球、茧、蚕丝、啤酒花、麦柴、草、废塑料袋等一切轻泡、松散物料。包型紧凑,整齐美观,可大幅降低运输成本,是棉产区、纺织企业、超市、服装厂、250T立式液压打包机废旧物资回收业和其他各种轻工业企业必备的生产工具 。 250T立式液压打包机
详情先容:

50T立式液压打包机

金属铜打包机(不锈钢打包机),
 配用动力:22KW,台时产量:3-5个包块,包重:800-1500KG,
油缸:Φ190*2支,操作方便,接上电源后打包 , 专用于一切轻泡、松散物料的打包。可应用于用于有色金属板材及型材和轻簿型塑料,棉、羊毛、废纸、废纸箱、废纸板、纱线、塑料、布匹、编织袋、针织绒、麻、麻袋、毛条、毛球、茧、蚕丝、啤酒花、麦柴、草、废塑料袋等一切轻泡、松散物料。包型紧凑,整齐美观,可大幅降低运输成本,是棉产区、纺织企业、超市、服装厂、废旧物资回收业和其他各种轻工业企业必备的生产工具 。
250T立式液压打包机
型号:250
公称压力主缸KN:2500
液体*大工作压力MPa:25
料箱尺寸长1500mm,宽700mm,高:1400mm
包块尺寸:长1100mm*宽:700 *高:(1000)mm
包块密度kg/m3:≥2200
单次循环时间S:65
电机功率KW:22
油缸行程:1200-1350MM
机器外形尺寸mm:长2600*宽2400*高4100。
整机重量kg;9000.
250T立式液压打包机使用说明:
本厂立式液压打包机使用68#液压油,连接电源三相380V,额定电流为40A,安装时要有接地保护,电机要根据所示方向运转才能启用,否则不能启动。油箱加入液压油方可启动使用。但当气温降低时液压油浓度大,机内的滤清器不能起到过滤作用,这时必须将滤清器拆出,待温度恢复后,方可生新安装使用。(注:滤清器应每月清洗1-2次)。
       溢流筏-控制该机的压力开关,旋转调压手转向右转为增压,向左转为减压,出厂前已调整好压力。但在使用过程中调压手轮可能有变位现象,导致压力升高或降低,这时需要生新调节压力,调压时应在运转中进行,同时把压板降至*低位置,调整溢流筏的调压手轮,调整压力不能高于或低于压力表所示的范围,压力的OMPA(100KG/1cm2)。旁杆-增强压的刚性和起导向作用,每次使用前应加油,起润滑作用。
      行程开关-控制该机的启动和停止的作用,因此要经常检查、维修、保养。手动转向阀-控制压板向上向下,停止的开关。
      1、手动转向阀打向下档位时压板自动向下工作,当废纸压到结实状态时,那阻力大于压力:压板不能再向下压,应把手动转向阀打向空档位置,停止加压,如果长期处于加压状态,会导致液压,电机、油泵长时间处于超负荷状态而使各机件损坏。
     2、手动转向阀打向升档位置,压板自动向上升到*高的位置,由行程开关控制自停,这时应把手动转向空档位置。完成一个工作程序。

250 tons of waste aluminum hydraulic balers
Metal copper packer (stainless steel baler),
 Equipped with power: 22KW,
Taiwan when the output: 3-5 mass,
Package weight: 800-1500KG,
Cylinder: Φ190 * 2,
Easy to operate,
 Connected to the power after packaging, dedicated to all light foam, loose material packaging. It can be used in non-ferrous metal sheet and profile and light-type plastic, cotton, wool, waste paper, waste paper box, waste paperboard, yarn, plastic, cloth, woven bag, knitted cashmere, hemp, Hair ball, cocoon, silk, hops, wheat chai, grass, waste plastic bags and so on all loose foam, loose material. It is a necessary production tool for cotton producing areas, textile enterprises, supermarkets, garment factories, waste materials recycling industry and other light industrial enterprises.
250 tons of double cylinder hydraulic baler
Model: 250
Nominal pressure master cylinder KN: 2500
Liquid maximum working pressure MPa: 25
Box length 1500mm, width 700mm, height: 1400mm
Bulk size: Length 1100mm * Width: 700 * Height: (1000) mm
Bulk density kg / m3: ≥2200
Single cycle time S: 65
Motor power KW: 22
Cylinder travel: 1200-1350MM
Machine dimensions mm: length 2600 * width 2400 * high 4100.
Weight kg; 9000.
Instructions for use:
The factory is equipped with 68 # hydraulic oil, connected to the power supply three-phase 380V, rated current of 40A, the installation should be ground protection, the motor should be operated according to the direction shown to be activated, or can not start. Fuel tank can be used to start the use of hydraulic oil. But when the temperature drops when the hydraulic oil concentration, the machine can not play a filter filter, then the filter must be removed until the temperature is restored before the new installation and use. (Note: the filter should be cleaned 1-2 times per month).
       Overflow raft - control the machines pressure switch, rotary pressure hand turn right to pressurized, turn left to decompression, the factory has been adjusted before the pressure. But in the course of the use of pressure handwheel may have a displacement phenomenon, resulting in increased or decreased pressure, then need to add a new regulation of pressure, pressure should be carried out in the operation, while the pressure plate to the lowest position, adjust the overflow Rafts of the pressure regulating handwheel, the adjustment pressure can not be higher or lower than the pressure gauge shown in the range of optimum pressure for OMPA (100KG / 1cm2). Side bar - to enhance the rigidity of the pressure and play a role, each should be used before the fuel, from the lubrication.
      Stroke switch - to control the machines start and stop the role, so often check, repair, maintenance. Manual steering valve - control the pressure plate up and down, stop the switch.
      1, manual steering valve to play down when the pressure plate automatically down work, when the waste paper to a strong state, that resistance is greater than the pressure: the pressure plate can not be pressed down, the manual steering valve should be turned to neutral position, stop Pressurized, if the long-term pressure state, will lead to hydraulic, motor, pump for a long time in a state of overload and damage to the parts.
     2, manual steering valve to the upshift position, the platen automatically rose to the highest position, controlled by the trip switch from the stop, then the manual should be turned to the neutral position. Complete a working procedure.

姓名:
电话:
您的需求:
 

信誉第一网投平台|澳门十大网赌信誉平台

XML 地图 | Sitemap 地图