信誉第一网投平台-澳门十大网赌信誉平台-登录

推荐产品
  • 压铸模温机 压铸模温机,压铸机专用模温机,使用工作温度高达350℃,采用...
  • 集中供料系统 集中供料系统采用微机集中自动控制,实现了对粒料的24小时连续...
  • 自动吸料机 300G微电脑全自动吸料机产品(又称真空吸料机,自动吸料机,...
  • 水式模温机 水式模温机 达安泰企业专业生产模温机,高光模温机,高光注塑...
  • 中央供料配件 中央供料配件-中央控制台 操作界面与运转状态显示面板数字化...
  • 中央供料系统 中央供料系统是为注塑车间的塑料产品生产而设计的,实现了不间断...
  • 塑料干燥机 标塑料干燥机特点:原料接触面为不锈钢设计。 精密压铸的铝制外...
  • 吸粉机 吸粉机原理的详细先容: 真空吸粉机,又称作:气动真空给料机...
  • 低速粉碎机 低速粉碎机系列特点: 1、 慢速塑料破碎机属于无筛网型塑料回...
  • 自动吸料机 自动吸料机:5HP真空自动吸料机产量高;达到时产800公斤输...
产品详情
  • 产品名称:液压打包机

  • 产品型号:30T
  • 产品厂商:其它品牌
  • 产品文档:
你添加了1件商品 查看购物车
简单先容:
液压打包机主要适用于废纸、塑料、铁屑、垃圾等松散物料的打包装,减少体积便于包装、运输以及减少储放空间。液压打包机其具有结构紧揍,结实牢固;经济实用、操作简便、安全可靠等特点,是物料包装、废旧回收等行业致富的理想设备。
详情先容:

30吨液压打包机
废纸打包机,纸箱打包机,
 配用动力:7.5KW,
台时产量:3-5个包块,
包重:200KG,
油缸:Φ150*1支,
型号:30
公称压力主缸KN:300
液体*大工作压力MPa:15
料箱尺寸长900mm,宽600mm,高:1400mm
包块尺寸:长900mm*宽:600 *高:(500-1000)mm
包块密度kg/m3:≥400
单次循环时间S:29
电机功率KW:7.5
油缸行程:900-1200MM
机器外形尺寸mm:长1450*宽1050*高3100。
整机重量t;1.4.
液压打包机使用说明
一、安装步骤
1、本机必须平稳放在混凝土上,基础视当地情况决定。
2、检查油箱底部放油口是否已关闭,确定关闭后再打开油箱顶部加油口密封盖。
注入约60KG68#液压油,液压油排号视当地气温及使用标准决定。[注!如果机型在60T以上,新机时必须分两次注油,**次注入液压油高度至油尺顶部(蓝**线)。待压板下压至底部再加注液压油至油尺底部(红**线)详细见操作说明4]
3、安装好本机电源线,电压及频率视当地电源决定,(注!电机和电器配件的电压及频率已按客户订购机器时的要求配置安装好)常规采用三相四线制,其中三条带电源线分别接入电相内相应的三个接线位,(图7左)另一条为接地防漏电保护线,应紧接机体外露金属表面,以防电器漏电伤人。
二、液压打包机操作方法:
1、通入电源:把电箱内空气开关(本机总开关)合上,先检查三相电源电压是否正常,(用仪表或探电笔测试)关闭电相门,查看电相门板表面红色电源指示灯是否亮起。
2、启动电机:把手动换向阀手柄(付图3)往下推至*底位(机体附有操作图标),然后把启动按钮NO按下(图5右下),(注:如装有急停开关机型的请把急停开关按箭头方向右旋,急停开关弹出即可),(图5右上)如正常情况下电机启动。
3、 检看电机转向:(图8)电机启动后,手动换向阀手柄在*下位时,如压板不能往下移。这时请必须马上查看电机旋转方向是否正确,电机旋转方向必须按箭头指示方向一致。如果电机转向相反时则机器不能正常使用,这时应把手动换向阀手柄往上拉至中档位。然后按下停止按钮OFF(或急停开关按下)停止电机运转。切断输入总电源,把三相电源线其中二相线互换再接上即可。再按操作1和2重新操作,(注!必须确定电机转向是否与箭头指示方向一致。)
4、注入油量的关健:当压板正常往下移时,压板在**次移动,移动速度是不均匀的。待压板移至底部或移动中突然停止又或移动中噪声加大,这种情况下应先把手动换向阀手柄往上拉至中位,把停止开关OFF或急停开关按下,停止电机运行。再仔细查看油箱储油量是否足够,如油量底于油箱高度一半时,证明油量不足,这时应再次往油箱注入适当液压油。这次加油量应加至油位尺*底界线(红**线)即可。
液压打包机操作方便,加60kg液压油,接上电源后打包 , 专用于一切轻泡、松散物料的打包。可应用于棉、羊毛、废纸、废纸箱、废纸板、纱线、塑料、布匹、编织袋、针织绒、麻、麻袋、毛条、毛球、茧、蚕丝、啤酒花、麦柴、草、废塑料袋等一切轻泡、松散物料。包型紧凑,整齐美观,可大幅降低运输成本,是棉产区、纺织企业、超市、服装厂、废旧物资回收业和其他各种轻工业企业必备的生产工具 。售后保障:
本产品享受三包服务,质保期为:一年质保。
服务承诺:
如有任何问题可与大家客服联系,大家会在**时间跟您沟通处理。大家将争取以*优惠的价格、*优的服务来满足您*大的需求。

液压打包机安装调试
关于需要大家提供上门安装调试的,请在签约时与业务人员确认,大家工程人员会现扬安装并提供操作人员和维护人员的专业培训。
无偿服务
大家无偿为您提供排废系统的整体方案,为您解决排废过程中所遇到的难题!
大家为您提供所有我司设备的电话技术支撑及解决方案,使您的设备系统能正常运行,从而保证整个生产线的流畅工作。
质保说明
打包机质保一年,从出厂之日起,人为损坏,易损件,自然灾害除外。一般报修后会在8小时内做出响应,大家技术人员会和现场工作人员联系,安排人员解决处理。如人为损坏或非质量损坏的,大家只收取配件及相应一些费用。质保期外,有偿提供配件及人员服务。
温馨提示:
由于部分产品的外观更换较为频繁,因此您收到的货品有可能与图片不完全一致,请您以收到实物为准,同时大家尽量做到及时更新,由此给您带来不便请多多谅解,谢谢!


液压打包机使用说明本机使用68#液压油,连接电源三相380V,额定电流为25A,安装时要有接地保护,电机要根据所示方向运转才能启用,否则不能启动。油箱加入60公斤的液压油方可启动使用。但当气温降低时液压油浓度大,机内的滤清器不能起到过滤作用,这时必须将滤清器拆出,待温度恢复后,方可生新安装使用。(注:滤清器应每月清洗1-2次)。
       溢流筏-控制该机的压力开关,旋转调压手转向右转为增压,向左转为减压,出厂前已调整好压力。但在使用过程中调压手轮可能有变位现象,导致压力升高或降低,这时需要生新调节压力,调压时应在运转中进行,同时把压板降至*低位置,调整溢流筏的调压手轮,调整压力不能高于或低于压力表所示的范围,*佳压力的OMPA(100KG/1cm2)。旁杆-增强压的刚性和起导向作用,每次使用前应加油,起润滑作用。
      行程开关-控制该机的启动和停止的作用,因此要经常检查、维修、保养。手动转向阀-控制压板向上向下,停止的开关。
      1、手动转向阀打向下档位时压板自动向下工作,当废纸压到结实状态时,那阻力大于压力:压板不能再向下压,应把手动转向阀打向空档位置,停止加压,如果长期处于加压状态,会导致液压,电机、油泵长时间处于超负荷状态而使各机件损坏。

     2、手动转向阀打向升档位置,压板自动向上升到*高的位置,由行程开关控制自停,这时应把手动转向空档位置。完成一个工作程序。

30 tons of vertical hydraulic balers

Waste paper baler, carton packer,
 Equipped with power: 7.5KW,
Taiwan when the output: 3-5 mass,
Package weight: 200KG,
Cylinder: Φ150 * 1,
Easy to operate, plus 60kg hydraulic oil,
 Connected to the power after packaging, dedicated to all light foam, loose material packaging. It can be used in cotton, wool, waste paper, waste paper box, waste paperboard, yarn, plastic, cloth, woven bag, knitted cashmere, hemp, sack, top, hair ball, cocoon, silk, hops, , Waste plastic bags and all the light foam, loose material. It is a necessary production tool for cotton producing areas, textile enterprises, supermarkets, garment factories, waste materials recycling industry and other light industrial enterprises.
30 tons of hydraulic balers
Model: 30
Nominal pressure master cylinder KN: 300
Liquid maximum working pressure MPa: 15
Box size 900mm long, width 600mm, height: 1400mm
Package Size: Length 900mm * Width: 600 * Height: (500-1000) mm
Mass density kg / m3: ≥ 400
Single cycle time S: 29
Motor power KW: 7.5
Cylinder travel: 900-1200MM
Machine dimensions mm: length 1450 * width 1050 * high 3100.
Machine weight t; 1.4.
Hydraulic baler instructions
Manual instruction
First, the installation steps
A
1, the machine must be placed on the concrete, the basic depending on the local situation.
1. the machine need to be installed on the concrete ground reposefully, the basic requirement as the actual location.
2, check the bottom of the fuel tank is closed, to determine the closure and then open the top of the tank filling port seal.
2. Need to check the oil boxs bottom which outlet whether closed or not, after closed caus then open the top of oil box and add the sealing cover for the top orifice.
Injection of about 60KG68 # hydraulic oil, hydraulic oil row number as the local temperature and the use of standard decisions. [Note! If the model is above 60T, the new machine must be filled with oil twice, the first time into the hydraulic oil height to the top of the dipstick (blue line). Press the press down to the bottom and then add the hydraulic oil to the bottom of the dipstick (red border) see the operating instructions in detail 4]
Immit around 60kgs No.68 # hydraulic oil, the optimal hydraulic oil shall be controlled or by the local citys no temperature & operation. [Remark: if the machine model will be more 50T, the new machine must separate to immit the hydraulic oil For the times the first time to immit till the hydraulic oils height to the top of oil meter (the blue color line). After the compressing plate move to the bottom then add the hydraulic oil again till the bottom of oil meter (the red Line), the details please check & study the operation 4].
3, the installation of the local power cord, voltage and frequency depending on the local power supply decision, (Note! Motor and electrical parts of the voltage and frequency of customer orders have been ordered to install the machine installed) conventional three-phase four-wire system, three With the power cord, respectively, into the electrical phase of the corresponding three wiring bits (Figure 7 left) and the other for the ground leakage protection line, should be exposed to the body exposed metal surface to prevent electrical leakage wounding.
3. According to the local city which voltage, frequency & phase to install the machines electric wires, (remark: the motor & electrical parts will be installed exactly as the buyers requirements when ordered the machine.) Normally use the 3 phase & 4 lines , And 3 pieces of electrical wires of them will be connected into the phase which relevant 3 connectors, (Picture 7 left), another line will be connected the ground for defending the creepage, the line shall be tightly connected the outside metals surface of the Machines body
Second, the operation method:
2. Methods of operation
1, access to power: the air box inside the air switch (the main switch) to close, first check the three-phase power supply voltage is normal, (with a meter or probe pen test) to close the electrical phase door, see the power of the door surface red power Whether the indicator light is on.
1. With the power: close the air switch of the electrical box (main switch of the machine), check the
Door opening, then the whole machine can not start. When the machine full of the materials
3 phase voltage whether is normal first (use the ammeter or electrical pen for testing), and closed the Electrical Phase door, then check surface red lamp of the phase doors plate
2, start the motor: the manual valve handle (pay Figure 3) down to the bottom (the body with the operation icon), and then press the button NO button (Figure 5 lower right), (Note: if installed There are emergency stop switch models, please put the emergency stop switch in the direction of the arrow, the emergency stop switch can pop up), (Figure 5 on the right) as normal under the motor start.
2. Start running motor: remove the manual changing direction handle (with picture 3) to the bottom (the machine with the operating sign), then impress the starter NO button (with the Picture 5 right down direction), (remark: if installed The following case of the crucible
3, check the motor steering: (Figure 8) After the motor starts, manual valve handle in the lowest position, such as the pressure plate can not move down. In this case, you must immediately check whether the direction of rotation of the motor is correct and the direction of rotation of the motor must be in the direction indicated by the arrow. If the motor turns to the opposite when the machine can not be used normally, then the manual valve handle should be pulled up to the mid-range position. Then press the stop button OFF (or the emergency stop switch is pressed) to stop the motor from running. Cut off the total input power, the three-phase power cord which can be connected to the two-phase line. And then press operations 1 and 2 to re-operate, (Note! Must determine whether the motor steering direction is consistent with the arrow.)
3. check the motors rotary direction: (with picture 8) after the motor started, when the manual changing direction valve handle which location is the lowest, if the compressing plate can not remove down, then must check the motors rotary side Immediately, the rotary direction of motor must same as the arrowheads direction. If the motors rotary direction is reverse then the machine can not run normally, then shall remove the manual changing valve handle up to the middle location, and impress the stopping switch OFF ( Or damage the emergency shutdown switch to to running running. Also turn off the electric power, and change the 2 phase lines of 3 phase lines then connect them again. And according to the Methods of operations 1. & (Remark: must sure the motors rotary direction any same as the arrowheads direction.)
4, into the fuel of the key: When the pressure plate down the normal move, the pressure plate in the first move, the movement speed is not uniform. To be pressed to move to the bottom or move suddenly stop or move the noise increases, in which case the manual valve should be pulled up to the middle of the handle, stop the switch OFF or emergency stop switch, stop the motor run. And then carefully check the tank oil storage is sufficient, such as oil at the end of the fuel tank height of half, to prove that the amount of oil, then again should be injected into the tank appropriate hydraulic oil. The amount of fuel should be added to the bottom line of the oil level (red line) can be.
4. the linchpin to immit the hydraulic oil: when remove the compressing plate down, when the compressing plate moving during the first time, the moving speed will be difference. After the compress plate moved to the bottom or during moving still stopping or during moving The noise was increased, during the condition then will remove up the manual changing valve handle to the middle location, impress the stopping switch OFF or emergency switch, st

姓名:
电话:
您的需求:
 

信誉第一网投平台|澳门十大网赌信誉平台

XML 地图 | Sitemap 地图