信誉第一网投平台-澳门十大网赌信誉平台-登录

推荐产品
  • 压铸模温机 压铸模温机,压铸机**模温机,使用工作温度高达350℃,采用...
  • 集中供料系统 集中供料系统采用微机集中自动控制,实现了对粒料的24小时连续...
  • 自动吸料机 300G微电脑*自动吸料机产品(又称真空吸料机,自动吸料机,...
  • 水式模温机 水式模温机 达安泰企业专业生产模温机,高光模温机,高光注塑...
  • 中央供料配件 中央供料配件-中央控制台 操作界面与运转状态显示面板数字化...
  • 中央供料系统 中央供料系统是为注塑车间的塑料产品生产而设计的,实现了不间断...
  • 塑料干燥机 标塑料干燥机特点:原料接触面为不锈钢设计。 精密压铸的铝制外...
  • 吸粉机 吸粉机原理的详细先容: 真空吸粉机,又称作:气动真空给料机...
  • 低速粉碎机 低速粉碎机系列特点: 1、 慢速塑料破碎机属于*筛网型塑料回...
  • 自动吸料机 自动吸料机:5HP真空自动吸料机产量高;达到时产800公斤输...
产品详情
  • 产品名称:150吨液压打包机

  • 产品型号:150T
  • 产品厂商:其它**
  • 产品文档:
你添加了1件商品 查看购物车
简单先容:
150吨液压打包机主要适用于废纸、塑料、铁屑、垃圾等松散物料的压缩包装,减少体积便于包装、运输以及减少储放空间。 150吨液压打包机其具有结构紧揍,结实牢固;经济**、操作简便、安***等特点,是物料包装、废旧回收等行业致富的**设备。
详情先容:

150吨立式液压打包机 
 配用动力:15KW,
台时产量:3-5个包块,
包重:200-800KG,
油缸:Φ160*2支,
150吨立式双缸设计
型号:150
公称压力主缸KN:1500
液体*大工作压力MPa:18
料箱尺寸长1100mm,宽700mm,高:1400mm
包块尺寸:长1100mm*宽:700 *高:(1000)mm
包块密度kg/m3:≥1000
单次循环时间S:45
电机功率KW:15
油缸行程:1200MM
机器外形尺寸mm:长1700*宽1400*高3900。
整机重量kg;5500.
150吨液压打包机使用说明:
本厂150吨液压打包机使用68#液压油,连接电源三相380V,额定电流为25A,安装时要有接地保护,电机要根据所示方向运转才能启用,否则不能启动。油箱加入120公斤的液压油方可启动使用。但当气温降低时液压油浓度大,机内的滤清器不能起到过滤作用,这时*须将滤清器拆出,待温度恢复后,方可生新安装使用。(注:滤清器应每月清洗1-2次)。
       溢流筏-控制该机的压力开关,旋转调压手转向右转为增压,向左转为减压,出厂前已调整好压力。但在使用过程中调压手轮可能有变位现象,导致压力升高或降低,这时需要生新调节压力,调压时应在运转中进行,同时把压板降至*低位置,调整溢流筏的调压手轮,调整压力不能高于或低于压力表所示的范围,**压力的OMPA(100KG/1cm2)。旁杆-增强压的刚性和起导向作用,每次使用前应加油,起润滑作用。
      行程开关-控制该机的启动和停止的作用,因此要经常检查、维修、保养。手动转向阀-控制压板向上向下,停止的开关。
      1、手动转向阀打向下档位时压板自动向下工作,当废纸压到结实状态时,那阻力大于压力:压板不能再向下压,应把手动转向阀打向空档位置,停止加压,如果长期处于加压状态,会导致液压,电机、油泵长时间处于超负荷状态而使各机件损坏。
     2、手动转向阀打向升档位置,压板自动向上升到*高的位置,由行程开关控制自停,这时应把手动转向空档位置。完成一个工作程序。
液压打包机使用说明书:
一、150吨液压打包机安装步骤
1、本机*须平稳放在混凝土上,基础视当地情况决定。
2、检查油箱底部放油口是否已关闭,确定关闭后再打开油箱顶部加油口密封盖。
注入约90KG,68#液压油,液压油排号视当地气温及使用标准决定。[注!如果机型在60T以上,新机时*须分两次注油,**次注入液压油高度至油尺顶部(蓝**线)。待压板下压至底部再加注液压油至油尺底部(红**线)详细见操作说明4]
3、安装好本机电源线,电压及频率视当地电源决定,(注!电机和电器配件的电压及频率已按客户订购机器时的要求配置安装好)常规采用三相四线制,其中三条带电源线分别接入电相内相应的三个接线位,(图7左)另一条为接地*漏电保护线,应紧接机体外露金属表面,以*电器漏电伤人。
二、150吨液压打包机操作方法:
1、通入电源:把电箱内空气开关(本机总开关)合上,先检查三相电源电压是否正常,(用仪表或探电笔测试)关闭电相门,查看电相门板表面红色电源指示灯是否亮起。
2、启动电机:把手动换向阀手柄(付图3)往下推至*底位(机体附有操作图标),然后把启动按钮**按下(图5右下),(注:如装有急停开关机型的请把急停开关按箭头方向右旋,急停开关弹出即可),(图5右上)如正常情况下电机启动。
3、 检看电机转向:(图8)电机启动后,手动换向阀手柄在*下位时,如压板不能往下移。这时请*须马上查看电机旋转方向是否正确,电机旋转方向*须按箭头指示方向一致。如果电机转向相反时则机器不能正常使用,这时应把手动换向阀手柄往上拉至中档位。然后按下停止按钮OFF(或急停开关按下)停止电机运转。切断输入总电源,把三相电源线其中二相线互换再接上即可。再按操作1和2重新操作,(注!*须确定电机转向是否与箭头指示方向一致。)
4、注入油量的关健:当压板正常往下移时,压板在**次移动,移动速度是不均匀的。待压板移至底部或移动中突然停止又或移动中噪声加大,这种情况下应先把手动换向阀手柄往上拉至中位,把停止开关OFF或急停开关按下,停止电机运行。再仔细查看油箱储油量是否足够,如油量底于油箱高度一半时,证明油量不足,这时应再次往油箱注入适当液压油。这次加油量应加至油位尺*底界线(红**线)即可。150吨液压打包机操作方便, 接上电源后打包 , **于**轻泡、松散物料的打包。可应用于棉、羊毛、废纸、废纸箱、废纸板、纱线、塑料、布匹、编织袋、针织绒、麻、麻袋、毛条、毛球、茧、蚕丝、啤酒花、麦柴、草、废塑料袋等**轻泡、松散物料。包型紧凑,整齐美观,可大幅降低运输成本,是棉产区、纺织企业、超市、服装厂、废旧物资回收业和其他**轻工业企业*备的生产工具 。
150 tons of vertical hydraulic balers
Scrap balers,
 Equipped with power: 15KW,
Taiwan when the output: 3-5 mass,
Package weight: 200-800KG,
Cylinder: Φ160 * 2,
Easy to operate,
 Connected to the power after packaging, dedicated to all light foam, loose material packaging. It can be used in cotton, wool, waste paper, waste paper box, waste paperboard, yarn, plastic, cloth, woven bag, knitted cashmere, hemp, sack, top, hair ball, cocoon, silk, hops, , Waste plastic bags and all the light foam, loose material. It is a necessary production tool for cotton producing areas, textile enterprises, supermarkets, garment factories, waste materials recycling industry and other light industrial enterprises.
150 tons of double cylinder hydraulic balers
Model: 150
Nominal pressure master cylinder KN: 1500
Liquid maximum working pressure MPa: 18
Box size 1100mm long, width 700mm, height: 1400mm
Bulk size: Length 1100mm * Width: 700 * Height: (1000) mm
Mass density kg / m3: ≥ 1000
Single cycle time S: 45
Motor power KW: 15
Cylinder travel: 1200MM
Machine dimensions mm: length 1700 * wide 1400 * high 3900.
Machine weight kg; 5500.
Instructions for use:
The factory is equipped with 68 # hydraulic oil, connected to the power supply three-phase 380V, rated current of 25A, the installation should be ground protection, the motor should be operated in accordance with the direction shown to be activated, or can not start. The tank to join the 150 kg of hydraulic oil can be used to start. But when the temperature drops when the hydraulic oil concentration, the machine can not play a filter filter, then the filter must be removed until the temperature is restored before the new installation and use. (Note: the filter should be cleaned 1-2 times per month).
       Overflow raft - control the machines pressure switch, rotary pressure hand turn right to pressurized, turn left to decompression, the factory has been adjusted before the pressure. But in the course of the use of pressure handwheel may have a displacement phenomenon, resulting in increased or decreased pressure, then need to add a new regulation of pressure, pressure should be carried out in the operation, while the pressure plate to the lowest position, adjust the overflow Rafts of the pressure regulating handwheel, the adjustment pressure can not be higher or lower than the pressure gauge shown in the range of optimum pressure for OMPA (100KG / 1cm2). Side bar - to enhance the rigidity of the pressure and play a role, each should be used before the fuel, from the lubrication.
      Stroke switch - to control the machines start and stop the role, so often check, repair, maintenance. Manual steering valve - control the pressure plate up and down, stop the switch.
      1, manual steering valve to play down when the pressure plate automatically down work, when the waste paper to a strong state, that resistance is greater than the pressure: the pressure plate can not be pressed down, the manual steering valve should be turned to neutral position, stop Pressurized, if the long-term pressure state, will lead to hydraulic, motor, pump for a long time in a state of overload and damage to the parts.
     2, manual steering valve to the upshift position, the platen automatically rose to the highest position, controlled by the trip switch from the stop, then the manual should be turned to the neutral position. Complete a working procedure.
Hydraulic baler instructions:
First, the installation steps
1, the machine must be placed on the concrete, the basic depending on the local situation.
2, check the bottom of the fuel tank is closed, to determine the closure and then open the top of the tank filling port seal.
Injection of about 90KG, 68 # hydraulic oil, hydraulic oil row number as the local temperature and the use of standards. [Note! If the model is above 60T, the new machine must be filled with oil twice, the first time into the hydraulic oil height to the top of the dipstick (blue line). Press the press down to the bottom and then add the hydraulic oil to the bottom of the dipstick (red border) see the operating instructions in detail 4]
3, the installation of the local power cord, voltage and frequency depending on the local power supply decision, (Note! Motor and electrical parts of the voltage and frequency of customer orders have been ordered to install the machine installed) conventional three-phase four-wire system, three With the power cord, respectively, into the electrical phase of the corresponding three wiring bits (Figure 7 left) and the other for the ground leakage protection line, should be exposed to the body exposed metal surface to prevent electrical leakage wounding.
Second, the operation method:
1, access to power: the air box inside the air switch (the main switch) to close, first check the three-phase power supply voltage is normal, (with a meter or probe pen test) to close the electrical phase door, see the power of the door surface red power Whether the indicator light is on.
2, start the motor: the manual valve handle (pay Figure 3) down to the bottom (the body with the operation icon), and then press the button ** button (Figure 5 lower right), (Note: if installed There are emergency stop switch models, please put the emergency stop switch in the direction of the arrow, the emergency stop switch can pop up), (Figure 5 on the right) as normal under the motor start.
3, check the motor steering: (Figure 8) After the motor starts, manual valve handle in the lowest position, such as the pressure plate can not move down. In this case, you must immediately check whether the direction of rotation of the motor is correct and the direction of rotation of the motor must be in the direction indicated by the arrow. If the motor turns to the opposite when the machine can not be used normally, then the manual valve handle should be pulled up to the mid-range position. Then press the stop button OFF (or the emergency stop switch is pressed) to stop the motor from running. Cut off the total input power, the three-phase power cord which can be connected to the two-phase line. And then press operations 1 and 2 to re-operate, (Note! Must determine whether the motor steering direction is consistent with the arrow.)
4, into the fuel of the key: When the pressure plate down the normal move, the pressure plate in the first move, the movement speed is not uniform. To be pressed to move to the bottom or move suddenly stop or move the noise increases, in which case the manual valve should be pulled up to the middle of the handle, stop the switch OFF or emergency stop switch, stop the motor run. And then carefully check the tank oil storage is sufficient, such as oil at the end of the fuel tank height of half, to prove that the amount of oil, then again should be injected into the tank appropriate hydraulic oil. The amount of fuel should be added to the bottom line of the oil level (red line) can be.

姓名:
电话:
您的需求:
 

信誉第一网投平台|澳门十大网赌信誉平台

XML 地图 | Sitemap 地图